EP20350MD341V11 - Cảm biến vị trí - MTS Sensor Vietnam - STC Viet Nam

Cảm biến vị trí – EP20350MD341V11 –  MTS Sensor Vietnam – STC Vietnam

Hãng sản xuất: MTS Sensor Vietnam

Xuất sứ: USA

Nhà cung cấp: STC Vietnam

Compact profile design for applications with limited spaces

• Ultra low designs for external mounting

• Multi-position measurement up to 2 magnets
• Outputs: Analog, CANbus, IO-Link, SSI, Start/Stop

Rod sensors – E-Series EH

• Fix the sensor rod via threaded flange.
• Note the fastening torque of 50 Nm.
• Seat the flange contact surface completely on the cylinder mounting surface
• The cylinder manufacturer determines the pressureresistant gasket (copper gasket, O-ring, etc.).
• The position magnet should not grind on the sensor rod.
• The piston rod drilling (Ø 10 mm rod: ≥ Ø 13 mm (≥ Ø 0.52 in.) borehole / Ø 7 mm rod: ≥ Ø 10 mm (≥ Ø 0.4 in.) borehole) depends on the pressure and piston speed.
• Adhere to the information relating to operating pressure.
• Protect the sensor rod against wear.

Profile sensors – E-Series EP / EL / ER / EP2

       The sensor is fitted on a flat machine surface using mounting clamps. A length-dependent number of these clamps are delivered with the sensor and must be distributed over the profile at regular distances. For fastening, we recommend using M5×20 screws (according to DIN 6912) that should be tightened with a fastening torque of 5 Nm.

Mọi thông tin chi tiết tư vấn , giải đáp về sản phẩm và được hỗ trợ giá tốt nhất xin vui lòng liên hệ:

Mr.Thanh

Email: thanh@stc-vietnam.com

Phone: 0965130856

Song Thanh Cong Trading Service Co., Ltd. (STC Vietnam)

Cảm biến vị trí – EP20350MD341V11 –  MTS Sensor Vietnam – STC Vietnam

Hãng sản xuất: MTS Sensor Vietnam

Xuất sứ: USA

Nhà cung cấp: STC Vietnam

Compact profile design for applications with limited spaces

• Ultra low designs for external mounting

• Multi-position measurement up to 2 magnets
• Outputs: Analog, CANbus, IO-Link, SSI, Start/Stop

Rod sensors – E-Series EH

• Fix the sensor rod via threaded flange.
• Note the fastening torque of 50 Nm.
• Seat the flange contact surface completely on the cylinder mounting surface
• The cylinder manufacturer determines the pressureresistant gasket (copper gasket, O-ring, etc.).
• The position magnet should not grind on the sensor rod.
• The piston rod drilling (Ø 10 mm rod: ≥ Ø 13 mm (≥ Ø 0.52 in.) borehole / Ø 7 mm rod: ≥ Ø 10 mm (≥ Ø 0.4 in.) borehole) depends on the pressure and piston speed.
• Adhere to the information relating to operating pressure.
• Protect the sensor rod against wear.

Profile sensors – E-Series EP / EL / ER / EP2

       The sensor is fitted on a flat machine surface using mounting clamps. A length-dependent number of these clamps are delivered with the sensor and must be distributed over the profile at regular distances. For fastening, we recommend using M5×20 screws (according to DIN 6912) that should be tightened with a fastening torque of 5 Nm.

Mọi thông tin chi tiết tư vấn , giải đáp về sản phẩm và được hỗ trợ giá tốt nhất xin vui lòng liên hệ:

Mr.Thanh

Email: thanh@stc-vietnam.com

Phone: 0965130856

Song Thanh Cong Trading Service Co., Ltd. (STC Vietnam)